Skip to content

Y811-52V — Visual Signaling Alarm Technical Manual ​

This manual covers the Y811-52V visual-only beacon in its three-color and seven-color configurations. Use the matching Y811-52V specification as the authority for the ordered supply, mounting, dimensions, and protection rating.

1. Safety and scope ​

Y811-52V provides auxiliary visual warning. It is not an emergency-stop circuit, a certified fire-alarm panel, a life-safety system, or a safety-rated control circuit.

Confirm the color configuration and the delivered wiring label before installation. The listed supply is DC 12-24 V. Disconnect power before wiring, changing the mounting, or opening the enclosure.

The manufacturer protocol manual lists IP65, while the product catalog lists IP55. Confirm the rating for the delivered configuration before selecting it for an installation that requires ingress protection.

2. Configurations and interfaces ​

ConfigurationControl optionAudioModbus color range
Three-colorThree switch inputs or Modbus RTU over RS485; select when orderingNoneRed, yellow, green
Seven-colorModbus RTU over RS485NoneRed, yellow, green, white, blue, cyan, purple

Both Modbus configurations use the shared protocol in sections 4-6. The three-color version uses the red, yellow, and green subset of the seven-color command set. A command for an additional color does not add that color to a three-color unit. Switch-input wiring applies only to the ordered switch-input version.

3. Installation and wiring ​

  1. Confirm the ordered color configuration and the model label.
  2. Use a regulated DC 12-24 V supply and observe polarity.
  3. Mount the beacon through the panel opening or with the supplied bracket.
  4. Keep RS485 wiring away from high-current and high-frequency switching wires.
  5. Assign a unique address before connecting multiple Modbus units to one bus.
  6. Confirm the final ingress-protection marking after the ordered configuration is received.

The manufacturer manual shows red for DC positive, black for DC negative, yellow for RS485 A+, and green for RS485 B-. Follow the label on the delivered cable if its wire colors differ. Do not connect an external voltage to a switch-input terminal until its electrical type has been confirmed.

4. Shared Modbus RTU commissioning ​

These serial parameters apply to both Modbus color configurations:

ParameterSupplied manual value
Physical interfaceRS485
Default device address01
Default baud rate9600 bit/s
Data bits8
Stop bits1
ParityNot stated in the supplied manual
Error checkingCRC16
Function codes0x06, write single register; 0x03, read holding registers

Confirm parity from the delivered configuration or protocol revision before commissioning. Use a short test cable and one device first. Calculate CRC16 over all bytes before the CRC field and transmit the CRC low byte first. Recalculate it after changing the address, register, or data.

The manufacturer defines 0xFF as a special address accepted regardless of the configured device address. Use it only with one device connected; use each device's unique address on a shared bus.

5. Shared light control ​

All byte values in command frames and the tables below are hexadecimal. Write register 0x00C2 with function code 0x06:

text
ADDR 06 00 C2 00 XY CRC_L CRC_H

ADDR is the device address. In the low data byte XY, the high nibble X selects the output mode and the low nibble Y selects the color.

XLight pattern
4Steady
5Slow flash
6Rapid flash
YColorAvailable configuration
1RedThree-color and seven-color
2YellowThree-color and seven-color
3GreenThree-color and seven-color
4WhiteSeven-color
5BlueSeven-color
6CyanSeven-color
7PurpleSeven-color
0OffThree-color and seven-color; use 0x0060 to switch off

For example, 0x0041 selects steady red, 0x0052 selects slow-flashing yellow, and 0x0067 selects rapid-flashing purple on a seven-color unit. The selected light state continues until another light-control command changes it or switches it off; the manual does not specify light-state retention after power-off.

Complete request examples for device address 0x01, including CRC:

ActionRequest frameConfiguration
Steady red01 06 00 C2 00 41 E8 06Both
Steady white01 06 00 C2 00 44 28 05Seven-color
Switch off01 06 00 C2 00 60 28 1EBoth

6. Status and communication settings ​

RegisterFunctionPurpose
0x00700x03Read one register containing the current light state
0x000B0x06Set the baud-rate selector
0x00C00x06Set the device address

Read the light state ​

text
Request:  ADDR 03 00 70 00 01 CRC_L CRC_H
Response: ADDR 03 02 DH DL CRC_L CRC_H

The manufacturer example returns DH DL = 00 42 for steady yellow. Its status table lists the red, yellow, and green states, but does not fully document readback for white, blue, cyan, and purple. Confirm those return values on the delivered seven-color unit before using them for status monitoring.

Change the device address ​

Write 00 NN to register 0x00C0, where NN is the new device address. The manufacturer documents values 0x00 through 0xFF and reserves special behavior for 0xFF. Use unique addresses 0x01 through 0xF7 for normal bus operation, and configure one device at a time. The new address takes effect immediately and is retained after power-off.

Change the baud rate ​

Write 00 NN to register 0x000B, where NN selects the baud rate:

SelectorBaud rate (bit/s)
0x019600
0x0219200
0x0338400
0x0457600
0x05115200
0x06256000
0x094800

After writing the selector, wait at least one second, then send the reset command (ADDR 06 00 0C 00 00 CRC_L CRC_H) or power-cycle the unit, and reconnect at the new baud rate. The setting is retained after power-off. The manufacturer also lists selector 0x07 as 35250 bit/s; confirm that unusual value before using it.

7. Troubleshooting and maintenance ​

SymptomLikely causeAction
No lightWrong supply, reversed polarity, or disabled outputCheck DC voltage, polarity, terminal labels, and the local command
RS485 unit does not replyA/B reversed, wrong address, baud, parity, or CRCTest one unit and check its communication parameters and CRC
Several units interfereDuplicate addresses or unsuitable bus wiringAssign unique addresses and use a daisy-chain bus
Protection is uncertainCatalog and manual use different IP ratingsUse the delivered marking and order confirmation

Inspect terminals, cable routing, mounting hardware, and the light window during scheduled maintenance.

8. Confirmation items ​

  • Final IP rating for the delivered configuration
  • Serial parity and seven-color status readback values for white, blue, cyan, and purple
  • Final connector and wire-color definition
  • Switch-input electrical type and active level

Source basis ​

  • Supplied product catalog, page 16: three-color YX523R and seven-color YX523RYB-7S
  • Manufacturer YX523R seven-color Modbus protocol manual, sections 2-4; the supplied filename is marked V1.1, while the document header and revision table state V1.0