Appearance
Y421-4444-L LoRa Wireless Analog and Digital I/O Module Specification


Confirm the ordered signal and frequency configuration on the supplied units.
1. Overview
Y421-4444-L uses a transmitter and receiver to transfer four analog and four digital signals in one direction. The transmitter provides four current inputs and four switch inputs; the receiver provides four corresponding current outputs and four relay outputs. The radio uses LoRa modulation; return messages in some modes do not provide a reverse I/O signal path.
2. Ordering Information
A link requires one transmitter and one receiver with compatible frequency and settings. Specify the nominal 433, 470, 868 or 915 MHz version and matching antenna when ordering. Confirm the supplied configuration and accessories before installation.
Choose compatible versions and antennas, and confirm the applicable frequency and radio settings for the destination before ordering.
470 MHz version: The center frequency is 470 MHz. Confirm the factory channel table and TX/RX RF output power before ordering; the factory starting frequency and all 16 channel frequencies are not specified.
3. Key Features
- Four 4–20 mA input-to-output channels and four switch-to-relay channels
- LoRa modulation and 16 selectable frequency channels
- Real-time and periodic transmission modes
- RS485 interface for parameter configuration
4. Technical Specifications
| Parameter | Specification |
|---|---|
| Supply voltage, each unit | 10–30 V DC |
| Operating temperature | -40 to +85 °C |
| Transmitter inputs | 4 current inputs and 4 switch inputs |
| Receiver outputs | 4 current outputs and 4 relay outputs |
| Analog signal | 0–20 mA input and output; supports 4–20 mA signals |
| Analog resolution | 12-bit |
| Analog accuracy | ±0.1%; reference and measurement conditions not specified |
| Digital input | Switch input, short to GND to activate |
| Relay output | Four normally open contact pairs; voltage, current and load ratings must be confirmed |
| Modulation | LoRa |
| Frequency options | 433, 470, 868 or 915 MHz; specify when ordering |
| RF output power | TX: 31 dBm typical at 433 / 470 MHz; 27 dBm stated at 868 / 915 MHz. Confirm RX transmit power before ordering. |
| Wireless channels | 16 selectable; default channel spacing 0.5 MHz, configurable |
| Antenna impedance | 50 Ω |
| Receive / transmit current, TX | < 50 mA / < 350 mA at 12 V and 25 °C |
| Receive / transmit current, RX | < 40 mA / < 300 mA at 12 V and 25 °C |
| Open-area range | Up to 5 km |
| Configuration interface | RS485 |
| Approximate dimensions | 90 × 115 × 40 mm; see mounting and connector clearances on the supplied unit |
| Weight | 143 g |
Current and RF figures are measured at 12 V and 25 °C. The stated analog accuracy has no specified reference, such as full scale or reading, and must not be used as a guaranteed end-to-end error. Range depends on antenna installation, obstructions and interference. Confirm relay ratings, analog loop wiring, output load and permissible input limits for the supplied units before installation.
Mechanical Dimensions

Dimensions are in millimeters. Allow additional space for the antenna and wiring; confirm mounting dimensions against the supplied unit.
5. Interfaces and Indicators
The transmitter provides IN/GND switch input pairs and A_IN/GND current input pairs. The receiver provides A_OUT/GND current output pairs and two terminals per relay output. Both units have power terminals, RS485 configuration terminals, an antenna connector and DIP switches. See the user manual for terminal assignments.
6. Important Notes
- Output behavior on communication loss depends on the selected mode. Test the supplied configuration with loads isolated.
- Do not use the wireless link as the sole emergency-stop or personnel-safety path.
- Manufacturer: Hunan YenGear Tech Co., Ltd.
- Email: [email protected]
- Website: www.yengear.com
