Skip to content

Y811-75AV — Multi-Color Sounder-Beacon Technical Manual ​

This manual covers the Y811-75AV three-color and seven-color sounder-beacon configurations. Both configurations share the wiring, serial settings, playback commands, and audio-file handling in sections 3-10. Their light values differ: sections 6.2, 6.3, and 7 give the three-color values, and section 11 gives the seven-color values. Use the Y811-75AV specification as the authority for the ordered supply, protection rating, dimensions, mounting, and control option.

1. Safety and scope ​

Y811-75AV provides auxiliary audible and visual warning. It is not an emergency-stop circuit, a certified fire-alarm panel, a life-safety system, or a safety-rated control circuit.

Both manufacturer manuals list a rated supply of DC 9-30 V and calls for a DC supply of no more than 30 V with a rated current of at least 1 A. The catalog lists DC 12-24 V or AC 220 V. Use the rating printed on the delivered unit; do not connect AC power or more than 30 V to a DC version. Disconnect power before wiring, mounting, opening the light cover, or replacing audio files.

The catalog lists IP55 and both manufacturer manuals list IPX65. Use the marking on the delivered unit as the final authority.

2. Configurations ​

ConfigurationLight colorsControl optionsManufacturer documentation
Three-colorRed, yellow, greenThree switch inputs (high-level or low-level trigger), or Modbus RTU over RS485Full manual: YX75R-RYG V1.3
Seven-colorRed, yellow, green, white, blue, cyan, purpleModbus RTU over RS485; three switch inputs listed but not documentedFull manual: YX75R-RGB V1.0

Common parameters from both manufacturer manuals: 5 W audio output (12 V supply, 8 Ω speaker), 0-100 dB sound level, MP3 up to 192 kbps, 70 Hz to 13 kHz frequency response, 8 MB built-in flash, steady, slow-flash, and rapid-flash light patterns, and a 75 mm diameter x 49 mm height enclosure.

3. Installation and wiring ​

Mount the unit with M4 screws in the three threaded inserts, which form a 40 mm triangle, or on the magnetic base. Use screw mounting where vibration is present.

The yellow and green conductors have different functions on the switch-input and Modbus versions. Confirm the control option on the label before connecting any wire.

3.1 Modbus version ​

ConductorFunction
RedDC positive
BlackDC negative
YellowRS485 A+
GreenRS485 B-

Connect A+ and B- to the controller or a USB-RS485 converter. Use a twisted pair and a daisy-chain bus for several units.

3.2 Switch-input versions (three-color) ​

ConductorHigh-level trigger versionLow-level trigger version
RedDC positive and trigger commonDC positive
BlackDC negativeDC negative and trigger common
YellowInput 1Input 1
GreenInput 2Input 2
BlueInput 3Input 3
  • High-level version: an input triggers when it is connected to the positive supply, or when 3.2 V ± 0.5 V to 24 V is applied relative to the unit's ground.
  • Low-level version: an input triggers when it is connected to ground, or when its voltage is 0 V to 0.7 V ± 0.1 V.
  • The trigger source must share ground with the unit.
  • Each input plays its own sound. Inputs suit PLC outputs or normally open switches.

4. Configuration file ​

The configuration file is documented in the three-color manual. The seven-color manual refers to a configuration file for the address and volume but does not give its format; confirm the format before using it on a seven-color unit.

4.1 Switch-input behavior ​

The trigger mode and the light behavior of the switch-input versions are set by a configuration file (section 4.2).

Digit 1Trigger modeBehavior
0Pulse, interruptible (default)Each trigger plays the sound once; a new trigger interrupts the current sound
1Level, loopingThe sound loops while the input stays active and stops when it is released; a new trigger interrupts
2Pulse, not interruptibleEach trigger plays the sound once; triggers during playback are ignored
3Pulse, looping, not interruptibleThe sound loops while the input stays active and finishes the current play when released; triggers during playback are ignored
4Pulse, single-track loopOne trigger starts a loop and the next trigger stops it; another input switches to its own sound
Digit 6Light during playback
1Steady during playback, off after playback
2Slow flash during playback, off after playback
3Rapid flash during playback, off after playback

Digits 1 and 6 apply only to switch-input versions. On Modbus versions, set digit 1 to 0.

4.2 File format ​

Create one plain-text (.txt) file in the root directory of the audio memory, using the USB connection in section 9. The file holds six digits:

DigitsSettingRangeDefault
1Trigger mode0-40
2-3Volume01-3030
4-5RS485 device address00-9901
6Light pattern for switch triggers1-3—

For example, 030013 selects trigger mode 0, volume 30, address 01, and rapid flash. Without the file, the unit uses pulse-interruptible mode. Never store more than one configuration file.

5. Modbus RTU commissioning ​

ParameterFactory default
Device address01
Baud rate9600 bit/s
Data bits8
Stop bits1
ParityNot stated in the manufacturer manual
Error checkingCRC16 (Modbus, polynomial 0xA001), low byte first
Default volume30

Every request is eight bytes:

text
ADDR FUNC REG_H REG_L DATA_H DATA_L CRC_L CRC_H
FieldMeaning
ADDRDevice address. 0xFF is a broadcast-style super address that any unit accepts; use it only with one unit connected
FUNC0x06 writes a control command; 0x03 reads a status value
REG_HLight state applied with a playback command; 00 for plain commands (section 6.2)
REG_LCommand code
DATA_H DATA_LCommand parameter

All values in this manual are hexadecimal. The manufacturer tables show xx xx in place of the CRC, and several printed CRC values are incorrect. Always calculate the CRC for the final frame. A unit echoes each accepted control command.

6. Control commands (function 0x06) ​

6.1 Command table ​

CommandFunctionParameter DATA_H DATA_L
0x0FPlay a file in a folderDATA_H folder 01-63 (01-99), DATA_L file 01-FF (001-255)
0x10Loop a file in a folderAs 0x0F
0x03Play by storage orderTrack number 0001-0BB8 (1-3000)
0x08Loop one trackTrack number
0x01Next track0000
0x02Previous track0000
0x0DPlay / resume0000
0x0EPause0000
0x16Stop0001
0x11Loop all tracks0001 on, 0000 off
0x17Loop a folderFolder 0001-0063
0x18Random playback0000
0x19Loop current track0000 on, 0001 off
0x04Volume up0000
0x05Volume down0000
0x06Set volume0000-001E (0-30)
0x09Select playback storage0001 USB disk, 0004 flash
0x0BSet baud rateSection 8
0x0CReset0000
0xC0Set device addressSection 8
0xC2Light control without changing playbackSection 6.3

Folder names must be 01 to 99, and file names must start with 001 to 255, for example 001alarm.mp3. The folder commands support MP3 and WAV files. A volume set by command returns to the configured volume after a restart; set a retained volume in the configuration file (section 4.2).

0x19 acts only while a track is playing. After a folder loop starts with 0x17, play, pause, next, and previous do not end the loop; send stop (0x16) to end it.

6.2 Light state with a playback command (three-color) ​

Put a light state XY in the REG_H byte of a playback command:

text
ADDR 06 XY CMD DATA_H DATA_L CRC_L CRC_H
XLight patternYColor
1Steady1Red
2Slow flash2Yellow
3Rapid flash3Green
6Off0No light

The lamp follows the selected state during playback and returns to its default state when playback ends. XY = 00 reuses the light state of the previous playback; after power-up, the lamp is off. XY = 60 plays audio with the lamp off.

Request (address 01)Action
01 06 11 03 00 01 BD 36Play track 1 with steady red light
01 06 31 0F 01 01 77 65Play folder 01 file 001 with rapid-flashing red light
01 06 60 03 00 01 A6 0APlay track 1 with the lamp off

6.3 Independent light control (0xC2, three-color) ​

text
ADDR 06 00 C2 00 XY CRC_L CRC_H

X is 1 steady, 2 slow flash, or 3 rapid flash; Y is 1 red, 2 yellow, or 3 green. XY = 60 switches the lamp off. The lamp keeps the commanded state until another light command changes it, and the command does not change the current playback.

Request (address 01)Action
01 06 00 C2 00 11 E8 3ASteady red
01 06 00 C2 00 23 69 EFSlow-flashing green
01 06 00 C2 00 32 A9 E3Rapid-flashing yellow
01 06 00 C2 00 60 28 1ELamp off

7. Status queries (function 0x03) ​

Send ADDR 03 00 CMD 00 00 CRC_L CRC_H. The response is ADDR 03 02 DH DL CRC_L CRC_H.

CommandQueryResponse
0x3FOnline storageDL = 08 means flash is online
0x42Playback stateDL = 00 stopped, 01 playing, 02 paused
0x43Current volumeDL = volume, for example 1E = 30
0x49Number of files in flashDH DL = file count
0x4DCurrent trackDH DL = track in storage order
0x70Sound and light stateSee below
0xFESoftware versionResponse format not documented

The 0x70 light values below apply to the three-color configuration; seven-color values are in section 11.3.

For 0x70, DH is the track now playing in storage order, and DH = 00 means no audio is playing. DL is the light state:

DLLight stateDLLight state
11Steady red23Slow-flashing green
12Steady yellow31Rapid-flashing red
13Steady green32Rapid-flashing yellow
21Slow-flashing red33Rapid-flashing green
22Slow-flashing yellowOther valuesLamp off

Example: 01 03 02 00 12 38 49 means no audio is playing and the lamp is steady yellow. The reported state can differ from the actual lamp if no light state was ever commanded.

8. Address and baud-rate settings ​

Device address. Write the new address to command 0xC0: ADDR 06 00 C0 00 NN CRC_L CRC_H. The usable range is 01-FE (1-254). An address in the configuration file takes priority over the command. The address takes effect immediately and is retained after power-off. Configure one unit at a time.

Baud rate. Write a selector to command 0x0B:

SelectorBaud rate (bit/s)SelectorBaud rate (bit/s)
01960005115200
021920006256000
03384000735250, as printed by the manufacturer; confirm before use
0457600094800

Wait one second, then send reset (0x0C) or power-cycle the unit. The new baud rate is retained.

9. Replacing audio files ​

  1. Disconnect the unit's power supply.
  2. Unscrew the light cover and connect the Micro USB port to a computer. The flash memory appears as a removable drive.
  3. Format the drive before copying new files to remove hidden files.
  4. Copy files one by one in the required play order. Commands 0x03 and 0x08 use the copy order, not the file name order.
  5. Use MP3 files at a supported sample rate: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, or 48 kHz.
  6. Disconnect the USB cable before powering the unit again.

10. Troubleshooting ​

SymptomLikely causeAction
Indicator off, no responseNo supply or wrong polarityCheck the DC voltage, polarity, and current capacity
Indicator steady, no audio after a command or triggerNo valid audio file, serial link not working, or wrong trigger levelCheck the files over USB; check A/B wiring, address, baud rate, and CRC; on switch-input versions, check the trigger version and common ground
Indicator flashing, no audioUnsupported audio fileRe-encode as MP3 at a supported sample rate, 192 kbps or lower
Audio breaks up at high volumeSupply voltage or current too lowUse at least DC 12 V with 1-2 A available
Wrong file playsCopy order differs from the intended order, or hidden files remainFormat the drive and copy files again in order
Settings ignoredMissing, misplaced, or duplicate configuration fileKeep exactly one .txt configuration file in the root directory
Protection is uncertainCatalog and manual use different IP ratingsUse the delivered marking and order confirmation

Inspect terminals, cable routing, mounting hardware, the light window, and sound openings during scheduled maintenance.

11. Seven-color light control ​

The seven-color configuration uses the same frames and commands as sections 5-9, with the light values below. These values are the same as Y811-95AV. Do not send the three-color values in sections 6.2 and 6.3 to a seven-color unit, or the seven-color values to a three-color unit.

11.1 Light state with a playback command ​

Put a light state XY in the REG_H byte of a playback command:

text
ADDR 06 XY CMD DATA_H DATA_L CRC_L CRC_H
XLight patternYColor
1Steady during playback, off after playback1Red
2Slow flash during playback, off after playback2Yellow
3Rapid flash during playback, off after playback3Green
4Steady, kept on after playback4White
5Slow flash, kept on after playback5Blue
6Rapid flash, kept on after playback6Cyan
0Off7Purple
0No light

XY = 00 reuses the light state of the previous playback; after power-up, the lamp is off. The manufacturer examples use XY = 60 to play audio with the lamp off.

Request (address 01)Action
01 06 31 03 00 01 B6 F6Play track 1 with rapid-flashing red light, off after playback
01 06 14 0F 01 01 7C 69Play folder 01 file 001 with steady white light, off after playback
01 06 47 03 00 01 AC BEPlay track 1 with steady purple light that stays on
01 06 60 03 00 01 A6 0APlay track 1 with the lamp off

11.2 Independent light control (0xC2) ​

text
ADDR 06 00 C2 00 XY CRC_L CRC_H

X is 4 steady, 5 slow flash, or 6 rapid flash; Y selects the color from the table in section 11.1. XY = 60 switches the lamp off. The lamp keeps the commanded state until another light command changes it, and the command does not change the current playback.

Request (address 01)Action
01 06 00 C2 00 41 E8 06Steady red
01 06 00 C2 00 57 69 C8Slow-flashing purple
01 06 00 C2 00 64 29 DDRapid-flashing white
01 06 00 C2 00 60 28 1ELamp off

11.3 Light status ​

For 0x70, the response is ADDR 03 02 DH XY CRC_L CRC_H. DH is the track now playing in storage order, and DH = 00 means no audio is playing. XY uses the same light-state values as section 11.1.

Example: 01 03 02 00 12 38 49 means no audio is playing and the light state is steady yellow with playback. The reported state can differ from the actual lamp if no light state was ever commanded.

The seven-color manual describes Modbus control only. It lists a three-switch-input option but gives no switch-input wiring or configuration-file table; confirm them on the delivered unit.

12. Confirmation items ​

  • Supply range, AC 220 V availability, and final IP marking for the ordered unit
  • Control option and trigger-level version
  • Serial parity on the delivered unit
  • Seven-color switch-input wiring, trigger level, and trigger behavior

Source basis ​

  • Manufacturer YX75R-RYG Modbus sounder-beacon manual V1.3, sections 2-8: three-color configuration
  • Manufacturer YX75R-RGB Modbus sounder-beacon manual V1.0, sections 2-6: seven-color configuration
  • Supplied product catalog, page 17: three-color YX75RYG and seven-color YX75RGB-7S